Martin Atomic 3000 Led – 3000W DMX Led Strobe

Physical Length: 245 mm (9.7 in.) Width: 425 mm (16.8 in.) Height: 240 mm (9.5 in.) Weight: 7.8 kg (17.2 lbs.) All data including mounting bracket

Dynamic Effects Strobe: 0.289 – 16.667 Hz, variable flash rate, intensity and duration Special effects: Blinder, ramp up/down, random flash, lightning. spikes, pre-programmed FX Aura (secondary LED array illumination) color mixing: RGB

Control and Programming Control systems: DMX, RDM Setting and addressing: Control panel with backlit monochrome graphic display DMX channels: 3/4/14 DMX compliance: USITT DMX512-A RDM compliance: ANSI/ESTA E1.20 RDM Transceiver: RS-485 Firmware update: USB memory key or via DMX with Martin™ M-DMX interface

Optics and Photometric Data Max. total output: 180,000 lumens* Beam (strobe) array:

Light source: 228 x Cree XLamp XP-L, 10 W white LEDs (color temperature 5,700 K)
Resolution: 8-bit
Dimming, above 16.7% output intensity: Current-controlled, flicker-free
Dimming, below 16.7% output intensity: PWM (refresh rate 6,000 Hz)
Minimum LED lifetime: 50,000 hours**

Aura (backlight) array:

Light source: 64 x Osram RGB LEDs
Resolution: 8 bits per color plus 8-bit dimming
Dimming: PWM (refresh rate 1,001 Hz)
Minimum LED lifetime: 50,000 hours**

*For full photometric data, click on Photometrics in menu bar
**To >70% output, figure obtained under manufacturer’s test conditions

Construction Housing: Steel. high-impact thermoplastic, flame-retardant to UL 94 5VA Color: Black Protection rating: IP 20

Installation Mounting points: Two pairs of quarter-turn fastener points, M12 holes in adjustable bracket Location: Indoor use only, must be fastened to structure or surface Orientation: Any Minimum distance to combustible materials: 200 mm (8 in.) from fixture Minimum distance to illuminated surfaces: 1 m (3 ft. 4 in.) from fixture

Connections AC Power: Neutrik PowerCON TRUE1 male socket DMX data in/out: 5-pin locking XLR Atomic Colors color gel scroller: 4-pin locking XLR Software upload: USB 2.0

Electrical AC power: 100-240 V~ nominal, 50/60 Hz Power supply unit: Auto-ranging electronic switch mode Rated current consumption: 3.5 – 8.4 A Peak current consumption: 17.7 A Typical half-cycle RMS inrush current: 17.7 A Maximum power consumption: 740 W

Typical Power and Current 100 V, 60 Hz: 663 W, 6.8 A, PF 0.98 120 V, 60 Hz: 655 W, 5.7 A, PF 0.96 208 V, 60 Hz: 645 W, 3.5 A, PF 0.89 230 V, 50 Hz: 642 W, 3.2 A, PF 0.88 240 V, 50 Hz: 642 W, 3.1 A, PF 0.87 Measurements made at nominal voltage with all LEDs at full strobe intensity. Allow for a deviation of +/- 10%. Allow for peak currents that exceed these figures when using the blinder effect. PF = power factor.

Thermal Cooling: Forced air (temperature-regulated, low noise, user-definable fan settings) Maximum ambient temperature (Ta max.): 40° C (104° F) Typical heat dissipation (calculated, +/- 10%): 2270 BTU/hr.